Nordic hot tub sl code

SLP or SL Message. Flex Pipe PVC Flow Switches.

In addition to the Sn Sn1 Sn2 type of error codes other codes for Smart Sensor spas such as SA Sb SnA SnB error codes are used on many spas and hot tubs.

Nordic hot tub sl code. SLP or SL Message. If the SLP or SL Message is Alternating with the Water Temperature on the Display the Spa is Operating in the Sleep Heating Mode. If the SLP or SL Message is ON Solid Not Flashing on the Display the Spa is Operating in the Sleep Heating Mode but there is No current water temperature because the Spa is between Filter Cycles.

How to get a hot tub to exit SL sleep mode. I have seen this happen with Cal Spas. On them you need to press the TEMP button and then the LIGHT button within three seconds of each other and this will change the modes from EC economy mode to SL sleep mode and finally to ST standard mode which is what you want.

All Nordic Hot Tubs are configured for 240 volt operation at shipping. On 240 volt systems use a minimum of 8 AWG wire for runs less than 40 feet. Use 6 AWG wire for runs up to 100 feet.

Always use a 4-wire system. On 120 volt systems the Hot Tub must be connected to a dedicated 20 amp circuit. SLP or SL Message.

If the SLP or SL Message is Alternating with the Water Temperature on the Display the Spa is Operating in the Sleep Heating Mode. If the SLP or SL Message is ON Solid Not Flashing on the Display the Spa is Operating in the Sleep Heating Mode but there is No current water temperature because the Spa is between Filter Cycles. Ecn or Ec is Alternating with Temp.

Temperature sensor error or water is dangerously hot. High limit manual reset on heater is tripped. Pump may be air locked or water level low.

High limit fault water may be dangerously hot. So instead of always keeping a hot tubs water always ready for use or completely cold sleep mode will keep your hot tubs water at a temperature that can be easily raised in just a short time. While your hot tub is in sleep mode or SL SLP mode on some models the.

Anyone can sell Nordic Hot Tubs only the best will do when representing our brand. We genuinely appreciate the opportunity to provide you with the best hot tub available and know your new hot tub will provide you therapeutic wellness family enjoyment and soulful relaxation for years to come. 24 rows The hot tub is in Economy mode.

While in this mode your hot tub will only heat while it. 2004 nordic crown II will not heat. Replaced heater tube pressure sensor and water sensor.

Tub at 63 degrees. Code on panel says 63. Did nont raise temp in past 24 hours.

I already had a. People also ask what is sleep mode on a hot tub. SLEEP mode heats the spa water to within 20 degrees of the set temperature during the filter cycle.

For example if your spa is set for 100 degrees on sleep mode it will heat to 80 degrees and stop. One may also ask what does economy mode mean on a hot tub. The modes are explained below.

The temperature of the hot tub. HLoH Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112 F.

SEoP Sensor open or disconnected. Heater disabled but the spa is operational. SESH Sensor short nonfunctional.

Heater disabled but the spa is operational. PSoC Pressure switch open with circulating pump. HLoH Hi Limit Over Heat.

Hi limit sensor is disconnected or shorted or the spa temperature is above 112 F. SEoP Sensor open or disconnected. Heater disabled but the spa is operational.

SESH Sensor short nonfunctional. Heater disabled but the spa is operational. PSoC Pressure switch open with circulating pump.

In addition to the Sn Sn1 Sn2 type of error codes other codes for Smart Sensor spas such as SA Sb SnA SnB error codes are used on many spas and hot tubs. These are similar to the Sn1 and Sn2 codes signaled from the high limit or water temperature sensors. When you have spa trouble codes of Sn SnA Sn1 Sn2.

Sn3 HL EO E2 E3 Prh Prr - these all refer to the heat. CTI Spa Side Error Codes. For more information regarding CTI tech support click here.

On startup indicates temperature probe problem. On startup indicates temperature probe problem. On startup indicates water temperature less than 39 F.

Overheating water over 112 F. System will restart when temp. Bath Tub Plumbing Assembly Kit.

Circulating Pumps. Flex Pipe PVC Flow Switches. What To Do If Your Hot Tub Has A FLO Error Code.

NorthWind Hot Tubs by Coast Spas Manufacturing Inc. 2 TABLE OF CONTENTS. Tional Electrical Code ANSINFPA 70.

The disconnect must be readily accessible and visible to the hot tub occupant but installed at least 5 feet 15 m from the hot tub water. When youre searching for a hot tub youre looking to add somewhere to relax and unwind at home. Nordic crafts their hot tubs with the customer in mind with superior quality and a passion for hot water therapy.

Step in and experience the tranquility of a Nordic Hot Tub for yourself.