Lte parameters user guide

Title page TDD eNodeB LTE Parameters User Guide LTE Parameters User Guide LPUG LPUG. WIRELESS SUPERVISION AND PRACTICE YOUR KNOWLEDGE.

This guide briefly describes the appearance of the LTE E8372 and the steps for using the LTE E8372.

Lte parameters user guide. Title page TDD eNodeB LTE Parameters User Guide LTE Parameters User Guide LPUG LPUG. This section will summarize the Basic parameters of the LTE. SC-FDMA Single Carrier Frequency Division Multiple Access supports 50Mbps 20MHz spectrum DL.

OFDM Orthogonal Frequency Division Multiple Access supports 100Mbps 20MHz spectrum. This section will summarize the Basic parameters of the LTE. UMTS FDD bands and TDD bands defined in 36101 v860 Table 551 given below.

FDD TDD half-duplex FDD. FDD eNodeB LTE Parameters User Guide 0613EN 4 September 2012 LTEIRCAPP027426 from DÉPARTEME 101 at Mohammed V University Agdal Rabat. 3 4T4R 4 Appendix Idle Mode Inter-RAT Reselection L2U U2L L2U.

Only when LTE RSRP -114dBm and UMTS RSCP -103dBm lasts for 1 U2L. Once LTE RSRP -108dBm lasts for 1 second then reselect to LTE second then reselect to UMTS If different reselection priority are set for different LTE frequency then UE will search the prioritize frequency first if no suitable cell then search second. LTE Parameters and Tuning RRC Inter-RAT State TransitionsBoth Inter-RAT Inter-Radio Access Technology handover and cell reselection are defined for LTE which means that defined state transitions must also be defined for interworking to the radio resource control states in other technologiesThe diagram shows the state transitions for UMTS and GSMGPRS.

4G LTE - RF Configuration Parameters Page 17 PRACH Planning I Project Preambles are generated from root sequence Zadoff-Chu sequence and its cyclic shift step Ncs. The radio protocol architecture for LTE can be separated into control plane architecture and user plane architecture as shown below. At user plane side the application creates data packets that are processed by protocols such as TCP UDP and IP while in the control plane the radio resource control RRC protocol writes the signalling messages that are exchanged between the base station and the mobile.

LTE Optimization Engineering Handbook is a comprehensive reference that describes the most current technologies and optimization principles for LTE networks. The text offers an introduction to the basics of LTE architecture services and technologies and includes details on the key principles and methods of LTE optimization and its parameters. This guide briefly describes the appearance of the LTE E8372 and the steps for using the LTE E8372.

For details about how to set the device and Wi-Fi management parameters see help information on the device management web page at httphuaweisetup or. Page 3 Getting to Know Your LTE E8372 The following figure shows the LTE E8372. The following sections detail notional diagrams of the sequences involved in sending data from the LTE-M Module up to the Link Labs Cloud Server uplink and from the Cloud Server down to the LTE-M Module downlink.

Please refer to the Command and Response specifications in the following section for exact details and parameters. Remaining modules identify the parameters used in vendor network and equipment. UNDERSTAND THE IDLE MODE BEHAVIOR.

PRACTICE YOUR KNOWLEDGE ON IDLE MODE. WIRELESS SUPERVISION AND PRACTICE YOUR KNOWLEDGE. POWER CONTROL IN LTE.

PRACTICE EXERCISE ON RANDOM ACCESS POWER. 14 parameters Samsung Galaxy S8 which should immediately change. To download the user manual go to the category of your equipment select the brand of your equipment then click on the model you are interested in.

Lte drive test parameters. LTE DRIVE TEST PARAMETERS RSRP - Reference signal receive power. RSRP dBm RSSI dBm -10log 12N where RSSI Received Signal Strength Indicator N.

Number of RBs across the RSSI is measured and depends on the BW Significance. RSRP is the most basic of the UE physical layer measurements and is the linear. LTE-Lite User Manual 212Supplied Accessories The LTE-Lite Evaluation Kit includes the LTE-Lite Evaluation Board and is supplied with a GPS antenna with 5m cable a USB cable a USB wall-wart power supply and two MMCX to BNC adaptor cables and is ready-to-go out of the box.

Figure22 LTE-Lite Evaluation Kit example Accessories 213USB Serial. FDD eNodeB LTE Parameters User Guide 0613EN 4-September 2012 LTEIRCAPP027426 INTERNAL Approved-Standard Volume 1. Introduction Passing on or copying of this document use and communication of its contents not permitted without AlcatelLucent written authorization Copyright 2012 by Alcatel-Lucent.

Third-party user equipment UE such as smartphones connects to the operators mobile network and influences the QoE but the operator only has limited control over 1 Introduction LTE_mobile_optimization-a_definitive_guide_wp_en_5216-2018-52_v0100indd 3 12102018 111824. B890 LTE Wireless Gateway User Guide EnglishNorwegianSwedishGerman. English Getting to know your device 1 Appearance 1.

IoT Solutions Software Products Services for the.